peacefrance68

Peugeot 208 Key Replacement It is best to delegate the replacement of Peugeot 208 keys to auto locksmiths with the necessary equipment and technical knowledge. They can create and program keys more quickly and at a lower cost than a dealership. A dead coin battery is most likely to be the cause the reason your key-fob stops locking or unlocking doors. However, there are many other reasons the key could be malfunctioning. Dead Coin Battery A dead battery in the coin compartment will prevent your Peugeot 208 from locking or unlocking, and won't start the engine. If this is the scenario, you'll need apply the backup starting technique which is explained in your vehicle's owner manual. Another reason why your 208 may not start is because the spark plugs have been damaged. Spark plugs are what ignite the fuel to start the engine. They only last for a certain amount of time. They will eventually break down when they aren't used enough. Luckily, there is an easy solution for this issue. The best way to solve this issue is to check the voltage of your car battery with a multimeter. If the voltage is below 11,5 volts, it's time to replace it. If the battery has corroded, it is important to clean its contacts. This can be done by lifting the rubber covers covering the two terminals on the battery and using a wire brush to remove any parts that are corroded from the battery. Then, you must reconnect the positive and negative pole cables. Water Damage If your 208 won't start and the battery has not gone flat, you should check the spark plugs. It is possible that they are overly dirty, causing them not to spark. The spark plugs can be cleaned in an workshop. Peugeot cars use a key with a transponder that is compatible with the immobiliser. This guarantees that only the right key can start the engine. If the chip inside the Peugeot key is damaged, it will not transmit the proper signal to the vehicle. Water damage is a typical cause of this issue. This is particularly common in colder climates, as the vehicle might have been exposed to snow or rain. If this is the case, you should get in touch with a reputable locksmith who will have all the tools and equipment required to reprogram the new key. They will also have the most up-to-date technological know-how and machinery required to create a Peugeot 208 smart key. The process shouldn't take more than 15 minutes. Faulty battery contacts Peugeot replaced the old transponder chips with a brand new model that is based on electronic components mounted on a circuitboard. The new system works great in its initial state, but the circuit boards deteriorate over time and stop working properly. This can stop the immobiliser chip activating which means that your car won't start. If this is the case, it's a good idea call a Peugeot specialist or locksmith. Another issue that is common is when the battery of the key fob starts to die, this causes the key blade to stop getting into the lock. A car locksmith can replace the battery and cut a new blade for you, it's generally a quick fix. Faulty Receiver Module If your Peugeot key fob stopped working after dropping it on the floor, being exposed to a sudden rain or accidentally washing it may be due to a faulty receiver module. The receiver module is responsible for transmitting radio frequency to the onboard computer which regulates the central locking system of your Peugeot vehicle. The rubber seals on the key fob block water from reaching the electronic chip. The chip can be damaged by water when it is exposed to water for a prolonged period of time. Submerging the key fob into sea water at the beach or throwing it into the pool can be particularly damaging due to the high salt content. If your Peugeot spare key fob stops working, you'll need to have the module replaced. This should be done by a Peugeot specialist or expert auto locksmith. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the right programming to allow the car to start. This is the reason why you should only be able to trust a professional Peugeot locksmith with the task of designing and programming an alternative. Computers with faulty on-board computers The computer on board of your Peugeot is responsible for a variety of features in your car, including power windows and airbags. If car keys goes wrong with these systems, it'll typically display a code that identifies the issue. This code will be saved in the system until the problem is fixed. Often, this will involve replacing the on-board computer. The most typical reason for the airbag warning light to flash is corrosion or loose connections in the sensor. This can be caused by wear and tear, aging, exposure to salt and moisture. It is important to have this issue resolved as soon as possible, as a malfunctioning airbag can be dangerous in the event of an accident. If you find an error message stating that the card is not found on your Peugeot, the key battery in the key fob may be dead or weak. This will prevent the key fob from sending a signal to disable your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then trying to start your vehicle. If it doesn't work then the battery in the key fob has to be replaced.